Arduino Boards
DC AC 7V-27V Motor Reversing Module Solenoid Valve Pump Controller Double Two Channel Relay
$15.13
Feature:
Product type: YYB-5
Function introduction: 6 kinds of commonly used functions; can control 2-way solenoid valve, water pump, motor and lights
Input voltage: DC / AC 7V – 27V
Output power: Can control DC or AC load within 30A
Time range: 0.1 seconds to 999 minutes adjustable at any time
Terminal Description:
1. AC / DC: Input power DC / AC 7V ~ 27V
2. IN1: signal input 1 (negative trigger)
3. IN2: signal input 2 (negative trigger)
4. IN3: signal input 3 (negative trigger)
5. NO: normally open relay interface, the relay hanging before pull-in, after pulled shorted connect to COM
6. COM: relay common interface
7. NC: normally close relay interface, the relay is shorted connect to COM before pull-in, after pulled hanging
Function list:
P – 1: Offer signal 1, relay 1 is automatically stopped when it is pulled to A time; offer signal 2, relay 2 is automatically stopped when is pulled to B time; Signal 3 is the emergency stop reset signal
P – 2: Offer signal 1, relay 1 is automatically stopped when it is pulled to A time; relay 2 is automatically stopped when the signal starts to delay B time then pull-in to C time (this function needs the same time unit)
P – 3: After power on, the relay 1 is pulled to release at A time, wait for the C time, the relay 2 pull to the B time to release, waiting C time; relay 1, 2 work endless loop
(If you control the motor forward and reverse can be understood as: motor forward in a period of time; stop for a period of time; automatically reverse a period of time; stop for a period of time; and then automatically forward; so cycle)
P – 4: Offer signal 1, relay 1 pull-in; offer signal 2 (limit), relay 1 stops and starts counting to A time, relay 2 pull; offer signal 3 (limit), relay 2 stops and starts counting to B time, relay 1 pull; infinite loop
(If the control of motor forward and reverse can be understood as: press the start button 1; motor is forward to limit 2 to stop for a period of time; automatically reverse to limit 3 to stop for a period of time; and then automatically forward; so cycle)
P – 5: Offer signal 1, relay 1 pull; offer signal 2 (limit), relay 1 stops and starts counting to A time, relay 2 pull; offer signal 3 (limit), relay 2 stop; give signal 1 agagin; execute again
(If you control the motor forward and reverse can be understood as: press the start button 1, motor is forward to limit 2 to stop for a period of time; automatically reverse to limit 3 stop; give signal 1 again; execute once again)
P – 6: Offer signal 1, relay 1 pull; offer signal 2 (limit), the relay 1 stop; give the signal 1 again, relay 2 pull; give signal 3 (limit), the relay 2 stop;
(If the control of motor forward and reverse can be understood as: press the start button 1; forward to limit 2 stop; press the start button 1 again; reverse to limit 3 stop;
Key Settings Description:
Power display "—-" means to enter standby mode;
Press the first times of K1, the display shows: P-1: K2 and K3 adjustment modes
Press the second K1, the screen displays: A001: K2 and K3 adjust the first time A, K4 adjust the decimal point (time unit)
Press the third K1, the screen displays: B001: K2 and K3 adjust the second time B, K4 adjust the decimal point (time unit)
Press the fourth K1, the screen displays: C001: K2 and K3 adjust the third time C, K4 adjust the decimal point (time unit)
Press the fifth K1, display "—-" indicates that the standby state;
For example, set mode P – 2, the time is: A010 B005 C006: Means the second working way; after offer signal 1; relay 1 start after 10 seconds closed; relay 2 offer signal again, after 5 seconds delay start 1 second automatically shut down
Decimal Point Time Unit Description:
XX.X: 0.1 to 99.9 seconds
XXX: 1 to 999 seconds
XXX.: 1 to 999 minutes
Package includes:
1 x Motor Reversing Module
