MHS-5200P+ Digital Dual-channel DDS Signal Generator Arbitrary Waveform Generator 6MHz-25MHz

Four frequency for you to choose: 6MHz, 12MHz, 20MHz, 25MHz Please choose the one you need.

Feature:

1, Direct digital synthesis (DDS) technology, FPGA design, low power consumption;
2, Dual output, can work in sync phase adjustable;
3, With up to 600 seconds of linear and logarithmic sweep sweep function;
4, With a sine wave, the basic function waveform triangle wave, square wave, sawtooth rise, falling sawtooth and variable duty cycle of the pulse wave, but also has 16 sets of arbitrary waveform customized by the user;
5, With M0 ~ M9 total of 10 sets of parameters stored bits M0 boot automatically transferred out of data;
6, At 15MHz or less, the sharpest of up to 15Vp-p, more than 12MHz, the biggest reach 8Vp-p;
7, Built sophisticated -20dB attenuator reach the minimum amplitude resolution 1mV;
8, With 120% ~ + 120% DC bias function;
9, Pulse duty cycle adjust accurate to 0.1%;
10, With four variable phase difference of TTL output;
11, Has a frequency measurement, period measurement, positive and negative pulse width measurement, duty cycle measurements and counting function;
12, Four optional frequency measurement gate time, which strike a balance between speed and accuracy;
13, All parametric EQ calibration can be performed by internal procedures;
14, Powerful communications features, completely open communications protocol, the secondary development becomes very simple;
15, After the connection with the PC, the PC can be used to control the instrument, and can be edited on the PC arbitrary waveform output waveform is downloaded to the instrument.
16, This model machine can be equipped with an increase in power module, the signal output amplitude reaches 30Vpp, the maximum output current reaches 1A;

The difference between MHS-5200P and MHS-5200P+, two models of the power amplifier parameters are as follows:

Project	MHS-5200P (ordinary)	MHS-5200P+ (broadband-type)
Signal bandwidth	DC (0kHz-80kHz)	DC (0kHz-5MHz)
Output signal amplitude	30mVp-p to 30Vp-p	30mVp-p to 30Vp-p
Maximum output current	1A	300mA
Maximum power output	15W*2 (dual-channel amplifier)	4.5W*2 (dual-channel amplifier)
Output short circuit protection	Yes (limiting)	Yes (limiting)
Output impedance	≤1Ω	≤1Ω
Output phase	In phase with the signal terminal	With the signal terminal of the inverter
Distortion	<1%	<1%
The output signal flatness	±1dB	±1dB

Grade	Explanation	Grade	Explanation
1	LCD1602	7	CH2 output interface
2	Status indicator	8	Amplifier interface
3	Operation button	9	DC12V power input
4	Knob	10	USB communication
5	Ext. In input interface	11	TTL_IO Input / Output
6	CH1 output interface	12	Power switch

Project		Parameter
External measurement	Frequency range	Sine wave	Normal mode: MHS-5200-06M: 0Hz-6MHz MHS-5200-12M: 0Hz-12MHz MHS-5200-20M: 0Hz-20MHz MHS-5200-25M: 0Hz-25MHz
		Square wave	0Hz-6MHz
		Triangle wave	0Hz-6MHz
		Sawtooth	0Hz-6MHz
		Arbitrary	0Hz-6MHz
		TTL digital signal wave	0Hz-6MHz
	Output modulation	Frequency sweep
	Waveform type	Sine, square, triangle, sawtooth lift, CMOS digital signal wave
	Waveform length	1024 points
	Sampling rate	200MSa/s
	Waveform amplitude resolution	8bits
	The minimum frequency resolution	10mHz
	Frequency error	±5×10^-6
	Counting range	0-4294967295
	Counting	Manually
	Positive and negative pulse width measurement	10ns resolution, the maximum measurable 10s
	Periodic measurement	20ns resolution, the maximum measurable 20s
	Duty cycle measurement	0.1% resolution, measuring range from 0.1% to 99.9%
	Source selection	Ext.IN input (AC signal) , TTL_IN input (digital signal)
Memory	Quantity	10
	Location	M0-M9
Interface	Interface	Using USB to serial interface
	Communication rate	57600bps
	Protocol	Using the command line, the agreement public
Power supply	DC	DC12V
Size	L x W x H	180 x 190 x 71mm
Weight	Single	680g